Pre-1995
Openers PRE-1995 OPENERS: This is easier done
prior to installation and near the opener. You only have 20 seconds
from the time the opener program button is actuated to send the security
code. Opener programming: To program a transmitter into an ACB equipped opener you will need to locate the programming buttons on the rear panel of the opener powerhead. You should see a small green LED and 3 small buttons labeled f+, f- and SC. You will momentarily press the SC
button once. The main light bulb will flash once. After a few
seconds, the light will remain on for approximately 5 seconds, indicating
the programming is complete. Operation: Press
the enter button, enter your 4 digit security code, and the “enter” button
again. (For additional safety, the enter button acts like a wall push
button during the travel of the door for approximately 15 seconds) This
allows you to quickly stop the door if necessary. Programming your Overhead Door Codedodger® wireless keypad: Resetting your keypad: If, at any time, during programming, you should enter the wrong PIN or make a mistake, you should reset the keypad to its factory setting. Open the keypad cover half way Press and hold the number 8 and the PROG buttons while opening cover fully. The indicator light will blink once and go out. Close the cover. You are now ready to re-program your keypad. Basic Programming Open cover fully Indicator will blink once and go out Press 3-5-7 Press PROG Indicator will blink once per second Enter PIN 1 (up to 8 digits) Press PROG Indicator will blink twice per second Close cover. Your keypad is now ready to be programmed to the garage door opener. Locate the Learn code button on your Codedodger garage door opener. Depending on model, the learn code button will be located under the light cover or on the rear panel. Basic Opener Programming Press the learn code button Learn code LED will flash Open cover on keypad fully Enter PIN number Press the SEND button 4 times, or until the door begins to operate. You will now be able to use your wireless keypad normally. Controlling a single door with your keypad Open keypad fully Press PIN number Press SEND once Door should operate normally NOTE: As a “panic” feature this keypad will operate door for up to 30 seconds from any button. Programming multiple doors with your keypad Program your keypad according to the steps outlined in the Basic programming section listed above. Open cover fully Enter PIN number Press PROG Indicator will blink once per second Press PROG Indicator will blink twice per second Press PROG Indicator will blink three times per second Enter the total number of doors (2 or 3) Press PROG Close cover Your keypad is now ready to be program to the garage door openers. Locate the learn code button on your garage door openers Press the learn code button once Learn code indicator will flash Open cover on keypad fully Enter PIN Press SEND Enter door number 1-2-or-3 Press send button 4 times, or until door operates Repeat these steps for door 2 and 3 Controlling multiple doors Open cover fully Enter PIN number Press SEND Enter door number (1-2-or 3) Chosen door should operate Adding PIN 2 Open cover fully Enter 1-5-9 Press PROG Indicator will blink once per second Enter PIN 2 (up to 8 digits) Press PROG Indicator will go out Close cover Your keypad is now ready to be programmed to the garage door opener. See steps in Basic programming. Adding a temporary PIN Open cover fully Enter PIN 1 Press PROG Indicator will blink once per second Press PROG Indicator will blink twice per second Enter temporary PIN Press PROG Indicator will blink three times per second Close cover Your keypad is now ready to be programmed to the garage door opener. See steps in Basic programming. Cancelling the temporary PIN The temporary PIN will remain active until PIN 1 is entered. Changing a PIN Open cover fully Enter PIN to be changed Press PROG Indicator will blink once per second Enter new PIN Press PROG Indicator will blink twice if PIN 1 has changed or go out if PIN 2 was changed Close cover. Your keypad is now ready to be programmed to the garage door opener. Locate the Learn code button on your Codedodger garage door opener. Depending on model, the learn code button will be located under the light cover or on the rear panel. Should you need additional information please contact our customer service department at 908-722-5785. PROGRAMMING FOR HOMELINK SYSTEM: Note: Some vehicles may require the ignition be turned on or the vehicle actually be running to program the Homelink transceiver. To program a rolling code compatible Homelink® system, please follow these steps. Press and hold the two outside buttons on the Homelink® system until the LED starts to blink, release buttons Press and hold the desired Homelink® button and the transmit button on your rolling code transmitter at the same time until the Homelink® LED changes from a slow blink to a rapid blink. (Your Homelink® system is now programmed) Locate the learn code button on your garage door opener. (These are located under the light cover or on the rear panel depending on model) Press the learn code button on the garage door opener, a red LED will start to blink. (You will have 30 seconds to complete programming) While the LED on the garage door opener is blinking, return to the vehicle and press the pre-programmed Homelink® button 4 times. (Or until the garage door operates). If you have problems programming, you might try these steps with the vehicle running. If you have problems with the Homelink® system please call 1-800-355-3515 or their website at http://homelink.jci.com/whyhomelink/index.html Homelink is a registered trademark of Johnson Controls, Inc.
|
|||||||||
| Copyright Overhead Door Company of Central Jersey © 2005 All rights reserved |